일리노이대학교 어버너-섐페인캠퍼스의 The 3D Printing Revolution 학습자 리뷰 및 피드백
강좌 소개
최상위 리뷰
DA
2021년 6월 13일
This course provides an overview and understanding of the 3-D printing industry, where it came from, where it's going, and where someone could start if they're interested in pursuing opportunities.
RP
2020년 6월 27일
A must attend course for those who like innovation and engineering. Will become a must complete subject for engineering graduates. This technology will definitely be a part of our day to day life.
The 3D Printing Revolution의 471개 리뷰 중 451~471
교육 기관: Himanshu P
•2020년 4월 5일
It's more for beginners of 3d printer learners .but real-life application is good to watch
교육 기관: Neftali W
•2016년 4월 30일
Good information but way too short for what Coursera charges.
교육 기관: LOKI S
•2020년 8월 21일
Looking for more technical aspect, but great course anyways
교육 기관: Doug N
•2021년 7월 23일
Educational, but lacks substance and a bit repetitive
교육 기관: MR. R G
•2020년 7월 3일
good course but try to add some technical content .
교육 기관: Mehran B
•2018년 3월 11일
the course wasn't as professional as I expected!
교육 기관: Erika L
•2021년 7월 22일
Needs updating, otherwise ok, easy to follow
교육 기관: Daryl m
•2016년 6월 28일
good introduction to 3D printing
교육 기관: David
•2016년 10월 20일
Not according what I expected
교육 기관: Aagam s s
•2020년 5월 21일
good
교육 기관: Dirk R
•2020년 4월 12일
Assignments are interesting and you fell the enthusiasm of the team. However, whole course is interviews only, no slides, nothing in writing (I am quite a visual type of learner, therefore bad for me). Each of probably more than 30-40 videos has the same title strip and the same trailer at the end, together more than a minute so that you waste around 40 minutes of your time seeing the same (marketing material for their university and lab). Furthermore technology does not work well. videos repeat and repeat unless you go back to course overview and select the next one.
Some of the quizzes show up before the videos, so that I was wondering why i could only guess to answer some of the questions, later realizing that answers were given in the following videos.
Some of the quiz questions really strange and not fully covered in videos (and see above, no slide or anything you could use to resume what you should have learned)
TO SUMMARIZE - REALLY EXCITING CONTENT BUT COURSE NEEDS SIGNIFICANT IMPROVEMENT
교육 기관: Cyndi W
•2016년 5월 20일
I didn't really care about the stories from the students or seeing the space for one whole lecture video. It's clear that Ultimaker is the sponsor, but it felt like a commercial. I want to learn more.
교육 기관: Deb K
•2020년 2월 7일
Good over view of technology, good list of references and resources to explore more on your own. Didn't really need to be 2 "weeks" worth. Audit for the info.
교육 기관: John w
•2020년 10월 6일
Great for someone who knows nothing about 3d printing, but overly simplistic if you have any concept of whats going on in that space.
교육 기관: LW
•2022년 2월 21일
Much of the information presented is outdated and unnecessarily lengthy.
교육 기관: Patrick S
•2019년 4월 1일
More of a promotional course than a learning course. You could learn most of the content here by finding a good news article. Videos are short and slow, if you took out the intro to each video and play them at 1.25 speed(as to not fall asleep). You can complete this course in 2 hours and get great scores on the quizzes.
교육 기관: Oleg R
•2016년 11월 26일
This course doesn't contain any new information. It does not teach you but just excitedly shows commonly known facts.
There are better ways to invest your time.
교육 기관: Sandeep G M
•2020년 4월 22일
Several glitches in Thingiverse. The interface the faculty shows is outdated. And there's no response from the support staff or the faculty.
교육 기관: Sajjan A
•2020년 7월 9일
in the assignment they should have not made it mandatory about uploading video
교육 기관: Giuseppe T
•2016년 5월 6일
It's not a course... this is a very short general introduction to 3D Printing
교육 기관: Martina B
•2017년 10월 18일
I did not really learn new technical skills.
Coursera Footer
