Chevron Left
Pressure, Force, Motion, and Humidity Sensors (으)로 돌아가기

콜로라도 대학교 볼더 캠퍼스의 Pressure, Force, Motion, and Humidity Sensors 학습자 리뷰 및 피드백

4.7
별점
86개의 평가
24개의 리뷰

강좌 소개

"Pressure, Force, Motion, and Humidity Sensors" can also be taken for academic credit as ECEA 5342, part of CU Boulder’s Master of Science in Electrical Engineering degree. This is our third course in our specialization on Embedding Sensor and Motors. To get the most out of this course, you should first take our first course entitled Sensors and Sensor Circuits. Our first course gives you a tutorial on how to use the hardware and software development kit we have chosen for the lab exercises. This third course assumes that you already know how to use the kit. After taking this course, you will be able to: ● Understand how to specify the proper AC or DC motor for a machine design. ● Integrate the motor to a machine, based on analysis of motor equations for voltage, current, torque and speed. ● Implement the motor and accompanying rotary sensor into a motor control circuit in both hardware and software. ● Add a motor and motor control circuit into a microprocessor based development kit. ● Create hardware and firmware to process motor feedback data to a microprocessor for further evaluation. After taking this course, you will be able to: ● Understand how to specify the proper pressure, force, strain, position, motion, acceleration, occupancy, and humidity sensors for taking real-time process data. ● Implement these sensors into an embedded system in both hardware and software. ● Add the sensor and sensor interface into a microprocessor based development kit. ● Create hardware and firmware to process sensor signals and feed data to a microprocessor for further evaluation. In this course you will build the circuit from Video 7 (Lab Exercise on strain gauges), Module 2 (Force and Strain Sensors and Touch Screens), and use it to make screen shots of the timing of the switch. If you haven't already wired up the system and written all the software per the instructions of Video 7, please do so now. You will need to buy the following components to complete this assignment. Note that if you have already purchased the PSOC 5LP PROTOTYPING KIT, you do not need to buy it again. These parts may be purchased off the Digikey web site, www. Digikey.com. One part needs to be purchased off the Sparkfun website www.sparkfun.com. Or, you may obtain the specs from the site, and purchase them elsewhere. Digikey Part numbers are typed out here: 428-3390-ND CF14JT22K0CT-ND CF14JT100KCT-ND Table shown here: Index Quantity Part Number Description 1 1 428-3390-ND PSOC 5LP PROTOTYPING KIT 2 2 CF14JT22K0CT-ND RES 22K OHM 1/4W 5% AXIAL 3 1 CF14JT100KCT-ND RES 100K OHM 1/4W 5% AXIAL Sparkfun part numbers are typed out here: TAL221 Table shown here: Index Quantity Part Number Description 1 1 TAL221 Mini-load cell - 100g, straight bar...

최상위 리뷰

PS

Nov 12, 2019

Um resumo,bem detalhista, sobre sensores e seus parâmetros para projeto.

HB

Jul 28, 2020

It was very good and superb course and it was also very hard to address

필터링 기준:

Pressure, Force, Motion, and Humidity Sensors 의 23개 리뷰 중 1~23

교육 기관: JiaJie, X

Jul 16, 2020

Overall the teaching content is good.

But I have to point out that the Quiz and Homework assignments are not carefully designed, that frequently found problem either the question is wrong, or belive is the registered "correct answer" is wrong. It can cause lots of confusion and frustration. It seems not only noticed by me but many similar posts in the forum, and none of the issue has been answered and addressed!

교육 기관: Paul P

Apr 10, 2020

The course has some good info. It needs a little polish

교육 기관: Pablo C S

Nov 12, 2019

Um resumo,bem detalhista, sobre sensores e seus parâmetros para projeto.

교육 기관: HET V B

Jul 28, 2020

It was very good and superb course and it was also very hard to address

교육 기관: Amit A

Jul 05, 2020

material collection are good and nicely designed Assignments.

교육 기관: Vinsensius C F

May 01, 2020

Overall, the materials explained can be well understood.

교육 기관: Enrique V

May 29, 2020

Very good course, build up nicely over previous one.

교육 기관: MR. V S

May 12, 2020

Good experience on solving problems.

교육 기관: Abhishek k

May 11, 2020

The videos and quiz were good .

교육 기관: KAUSTUBH K S

Apr 21, 2020

Good but somewhat difficult.

교육 기관: Bonifasius B S A

May 16, 2020

Good

교육 기관: Guillaume V

Apr 03, 2020

Important sensors are dealt with in this 3rd course. You will learn about physical effects (Peltier effect, piezoelectric effect), accelerometers. You will find one of those in many systems. Many readings.

교육 기관: KARIMULLA S

Aug 03, 2020

by answering the questions reading material is required. overall good

교육 기관: Ganesh R P

Jun 23, 2020

It is very knowledgeable Course. Mentor explains very well.

교육 기관: Neredikomma S R

Jun 12, 2020

It's really very informative and easily understandable.

교육 기관: Jos� R

Aug 03, 2020

Muy excelente curso

교육 기관: P S K R

Jun 12, 2020

It is quite good.

교육 기관: Steve A

Jun 11, 2020

Very useful .

교육 기관: chunduri B

Jul 28, 2020

good one

교육 기관: Benjamin V J

Jul 10, 2020

Awesome

교육 기관: NEELAM A

Jun 14, 2020

Good

교육 기관: Aritra B

May 30, 2020

Great course

교육 기관: YASH G

Jul 09, 2020

poor explanation trought out the course