Chevron Left
Sensor Manufacturing and Process Control(으)로 돌아가기

콜로라도 대학교 볼더 캠퍼스의 Sensor Manufacturing and Process Control 학습자 리뷰 및 피드백

4.6
별점
186개의 평가
42개의 리뷰

강좌 소개

"Sensor Manufacturing and Process Control" can also be taken for academic credit as ECEA 5343, part of CU Boulder’s Master of Science in Electrical Engineering degree. This is our fourth course in our specialization on Embedding Sensor and Motors. To get the most out of this course, you should first take our first course entitled "Sensors and Sensor Circuits", our second course entitled "Motor and Motor Control Circuits", and our third course entitled "Pressure, Force, Motion, and Humidity Sensors". Our first course gives you a tutorial on how to use the hardware and software development kit we have chosen for the lab exercises. Our second and third courses give you three hands-on lab experiments using the kit. This third course assumes that you already know how to use the kit. You will learn about sensor signal characterization and manufacturing techniques and how to optimize the accuracy of sensors. You will also learn about more advanced sensors, proportional-integral-derivative (PID) control, and how this method is used to give you a closed loop sensor feedback system. After taking this course, you will be able to: ● Understand how sensor manufacturers characterize and calibrate their sensors. ● Tune a PID control loop and access the PID control function of the Cypress PSoC development kit for a motor control application. ● Understand manufacturing methods used to build electro-mechanical and micro-machined sensors. You will need to buy the following components to do the two course projects based on the videos in this module. Note that if you have already purchased the PSOC 5LP PROTOTYPING KIT, you do not need to buy it again. These parts may be purchased off the Digikey web site, www. Digikey.com. Or, you may obtain the specs from the site, and purchase them elsewhere. All are quantity one except for N107-ND where you need three, and 493-15371-ND where you need two. 428-3390-ND P14355-ND FQU13N10LTU-ND N107-ND 1N5393-E3/54GICT-ND RNF14FTD1K00CT-ND P0.62W-1BK-ND 493-15371-ND Additional equipment needed: • Wire - various gauges and lengths • Breadboard • Oscilloscope – suggested models are: o PICOSCOPE 2204A-D2 available on www.digikey.com or o Digilent 410-324 | OpenScope MZ available on www.newark.com Depending on your budget, you can also investigate these models: o Hantek HT6022BE20MHz - https://www.amazon.com/dp/B009H4AYII o SainSmart DSO212 - https://www.amazon.com/dp/B074QBQNB7 o PoScope Mega50 USB - https://www.robotshop.com/en/poscope-mega50-usb-mso-oscilloscope.html o ADALM2000 - https://www.digikey.com/en/products/detail/analog-devices-inc./ADALM2000/7019661...

최상위 리뷰

KM
2020년 11월 15일

Great course to learn about\n\nSensor Manufacturing and Process Control in details.I highly recommend this course and thank you all.

GQ
2021년 4월 12일

This program is exceptional and really practical. Challenging computations in Process Control and Instrumentation .Awesome

필터링 기준:

Sensor Manufacturing and Process Control의 45개 리뷰 중 1~25

교육 기관: Guillaume V

2020년 5월 17일

I have learned a lot with this sensor specialization. Some selected application notes part from the reading material are very worth the time spent. The view is broad, sensor circuits, MEMS manufacturing techniques, etc. It helps me progress, better understand what I have seen in my career so far in the aerospace, electrical and medical industries.

교육 기관: G . p

2020년 6월 6일

This video session is very useful to learn both theoretical and practical

교육 기관: Bhargav c

2020년 7월 28일

good one

교육 기관: AKBAR A P

2020년 10월 13일

Good👍

교육 기관: Ngo T D

2021년 3월 13일

Great course, great content and learning material. It has real lab exercises with careful instructions. You can still do the assignment without real circuit, but learning by doing will be more efficient, and of course this subject needs real equipment.

The quiz is really helpful for each module lesson, but some of them are a bit difficult or having typing problem. Teachers should acknowledge and correct that. I hope lecture videos can have more animations about how devices work.

교육 기관: AMALNATH M P

2020년 10월 19일

Excellent Class and i learned more from here

교육 기관: Nithis r k

2020년 9월 21일

It's very useful

교육 기관: Samriddhi V K

2020년 5월 24일

please increase the contents...Descriptions in presentation slides are not enough well to get clear understanding though we went through the referred text books and links

교육 기관: Himanshu G

2020년 6월 1일

It was good.

교육 기관: Parishi N

2020년 4월 16일

some concepts in the first 2 weeks were not quite well explained

교육 기관: Sheikh A M

2020년 7월 2일

Instruction was not clear.

교육 기관: Kasuntha M

2020년 11월 16일

Great course to learn about

Sensor Manufacturing and Process Control in details.I highly recommend this course and thank you all.

교육 기관: Geoffrey S Q

2021년 4월 13일

This program is exceptional and really practical. Challenging computations in Process Control and Instrumentation .Awesome

교육 기관: KARIMULLA S

2020년 8월 21일

excellent ,we need more practice while solving the problem. material is very useful to answer the questions

교육 기관: kishan n c

2020년 9월 25일

have got a lot idea about industrial sensors and protocols and their construction theory

교육 기관: Ashab U

2021년 3월 17일

This course is very effective for practical process control and instrumentation

교육 기관: Elphus M

2021년 4월 23일

i find it to be life changing course, it is ery interesting

Thanks

교육 기관: Dean R

2019년 11월 17일

Great course, well done. Lots of good information here

교육 기관: Enrique V

2020년 6월 20일

This was the best course, I like the Labs :)

교육 기관: Dr.Krushnasamy V S

2020년 7월 4일

very toughest course.

But able to learn lot

교육 기관: Adetifa O O

2020년 12월 6일

Great course, now I know more on sensors

교육 기관: MUHAMMED S P

2020년 10월 18일

ക്ലാസ് വ്യത്യാസപ്പെട്ടിരിക്കുന്നു

교육 기관: Abelardo J R B

2021년 8월 18일

Excelente , todo muy dinámico.

교육 기관: Likhith B N

2021년 9월 21일

GOOD LEARNING EXPERIENCE

교육 기관: Kaparthi U

2020년 5월 15일

It is very useful course